⏱ 10 min read  ·  ✅ Updated Nov 2026

Introduction

A driveway takes a beating every day. Sun, rain, freeze-thaw cycles, oil drips, road salt, and tire wear all work on the surface, and a bare asphalt or concrete driveway shows the damage sooner than a sealed one. The right driveway sealer slows water intrusion, locks in loose aggregate, restores a dark uniform finish, and helps small surface cracks stay small instead of growing into potholes.

Our top pick: Liquid Rubber Driveway Restore, 5 Gallon. Runner-up: Armor SX5000 WB Deep-Soak Concrete Sealer, 5 Gallon.

Choosing a sealer is not a one-size decision. Asphalt and concrete need different chemistry. A rubberized coating that flexes with asphalt can trap moisture on concrete, while a deep-soak silane sealer that disappears into concrete does nothing for a rough blacktop surface. Volume matters too: a one-gallon jug suits crack work, while a five-gallon pail covers a full driveway in one or two coats.

This guide compares five driveway sealers that suit real homeowner jobs, from a full-driveway rubberized coating to a clear glossy concrete sealer and a cartridge crack filler for narrow joints. Each pick below includes honest pros and cons, a specs list, and guidance on where it fits, so you can match the product to your driveway surface, its condition, and the amount of work you are willing to do.

Affiliate Disclosure:

As an Amazon Associate, this site earns from qualifying purchases made through links in this article, at no extra cost to you.

Quick Picks

  • Best for Full Asphalt Driveways: Liquid Rubber Driveway Restore, 5 Gallon — a flexible water-based coating that fills cracks and renews worn blacktop.
  • Best Water-Based Concrete Sealer: Armor SX5000 WB, 5 Gallon — a deep-soak silane-siloxane sealer with a natural look for concrete, brick, and pavers.
  • Best Solvent-Based Concrete Sealer: Armor SX5000 Solvent-Based, 5 Gallon — a deeper-soaking matte sealer for dense concrete and stone.
  • Best for Narrow Cracks: Red Devil 0637 Asphalt Crack Filler, 10.1 fl oz, Pack of 4 — a cartridge acrylic filler that fits a standard caulking gun.
  • Best Clear Glossy Finish: Americrete A-1300 Clear Glossy Concrete Sealer, 1 Gallon — a transparent waterproofing coat for concrete driveways and floors.

1. Liquid Rubber Driveway Restore, 5 Gallon

Liquid Rubber Driveway Restore is a water-based asphalt coating built for homeowners who want to renew a tired driveway without hiring a crew. The flexible formula fills hairline cracks and small surface voids while laying down a uniform black coat, and it goes on with a brush, roller, or squeegee. Because it is water-based and low in volatile compounds, cleanup is simple and the smell during application stays mild compared with solvent coatings.

This is the pick to reach for when the whole driveway looks gray and weathered but the base is still sound. It is not a structural repair product, so wide cracks and settled areas need separate attention before coating. Applied in two or three thin coats, it builds a flexible membrane that resists water and helps the surface shed rain instead of soaking it up.

Pros:
– Flexible water-based coating that fills hairline cracks as it seals
– Applies with a brush, roller, or squeegee, no special tools needed
– Low odor and easy water cleanup compared with solvent sealers
– Five-gallon pail suits a full driveway in two coats

Cons:
– Needs two to three coats for full coverage, which takes time
– Not a fix for wide cracks, potholes, or settled pavement
– Drying time stretches in cool or humid weather

Specs

  • Type: Water-based asphalt coating and crack filler
  • Volume: 5 gallons
  • Coverage: 1 gallon per 50 sq. ft. at minimum final thickness
  • Application: Brush, roller, or squeegee
  • Surface: Asphalt driveways only

2. Armor SX5000 WB Deep-Soak Concrete Sealer, 5 Gallon

Armor SX5000 WB is a water-based silane-siloxane sealer that soaks into concrete, brick, pavers, and natural stone instead of forming a film on top. That soak-in action matters: the surface keeps its natural look and texture, and there is no glossy layer to peel, flake, or turn slippery when wet. It is a strong match for unsealed concrete driveways, paver driveways, and brick work where you want protection without changing the appearance.

Because it soaks in rather than coats, surface prep is the key step. The concrete must be clean and dry so the sealer can soak in evenly, and a garden sprayer gives the most even application. Once cured, it helps block water, de-icing salts, and oil stains from soaking into the pores of the concrete.

Pros:
– Soak-in formula protects without changing the surface look
– No film to peel or flake, and no added slipperiness when wet
– Water-based formula with low odor during application
– Works on concrete, brick, pavers, and natural stone

Cons:
– Requires a clean, dry surface for even soaking
– No glossy finish for buyers who want a wet look
– Five gallons is a lot for a small driveway or single walkway

Specs

  • Type: Water-based silane-siloxane deep-soak sealer
  • Volume: 5 gallons
  • Finish: Natural look, no sheen
  • Application: Pump sprayer recommended
  • Surface: Concrete, brick, pavers, natural stone

3. Armor SX5000 Solvent-Based Deep-Soak Concrete Sealer, 5 Gallon

The solvent-based version of Armor SX5000 uses the same silane-siloxane chemistry in a carrier that soaks in deeper into dense concrete and stone. That deeper reach makes it a good fit for older concrete, tightly troweled slabs, and pavers that have resisted water-based sealers. The cured finish is matte, so the driveway keeps a natural appearance while gaining protection against water and salt.

Solvent carriers come with trade-offs. Ventilation matters during application, and the odor is stronger than the water-based version. Cleanup needs a solvent rather than water. For buyers with dense or previously sealed concrete who need maximum soak-in depth, those trade-offs are worth it; for a first-time sealer on fresh porous concrete, the water-based version is the easier path.

Pros:
– Deeper soak-in for dense concrete and stone
– Matte finish keeps the natural look of the driveway
– Helps block water, salt, and oil stains from soaking in
– Five-gallon pail covers a large driveway

Cons:
– Stronger odor and ventilation needs during application
– Cleanup requires solvent, not water
– Overkill for fresh, porous concrete that the water-based version handles well

Specs

  • Type: Solvent-based silane-siloxane deep-soak sealer
  • Volume: 5 gallons
  • Finish: Matte, natural look
  • Application: Pump sprayer recommended
  • Surface: Concrete, brick, pavers, natural stone

4. Red Devil 0637 Asphalt Crack Filler, 10.1 fl oz, Pack of 4

Red Devil 0637 is a black acrylic crack filler in a standard caulking-gun cartridge, made for the narrow cracks that a full coating cannot fill on its own. Squeeze it into a crack, smooth it with a putty knife or gloved finger, and it dries into a water-resistant seal that flexes slightly with temperature change. The four-pack gives enough material for a driveway with scattered cracks without committing to a five-gallon pail.

This is a repair product, not a coating. Its job is to seal the gaps before you apply a full driveway sealer, or to touch up cracks between full sealing jobs. The acrylic formula adheres well to clean asphalt and concrete joints, and the cartridge format keeps the work neat and controlled.

Pros:
– Cartridge format fits a standard caulking gun for neat application
– Acrylic formula forms a water-resistant seal in narrow cracks
– Four-pack covers scattered cracks across a driveway
– Easy to use for quick touch-ups between full sealing jobs

Cons:
– Only suits narrow cracks, not wide gaps or potholes
– Four cartridges cover a limited total crack length
– Needs a clean, dry crack for good adhesion

Specs

  • Type: Acrylic asphalt crack filler
  • Volume: 10.1 fl oz per cartridge, pack of 4
  • Application: Standard caulking gun
  • Color: Black
  • Surface: Asphalt cracks and concrete joints

5. Americrete A-1300 Clear Glossy Concrete Sealer, 1 Gallon

Americrete A-1300 is a clear, glossy concrete sealer that waterproofs while giving the surface a rich, wet look. It suits concrete driveways, garage floors, sidewalks, and cinderblock work where the owner wants both protection and a visible finish upgrade. The transparent coat lets the concrete texture show through while adding a sheen that makes the surface look freshly poured.

The one-gallon size fits smaller jobs and test sections well, and the glossy film builds best on clean, dry concrete applied in thin, even coats. Because it forms a surface film, it needs sound concrete underneath: flaking or dusty surfaces should be cleaned and repaired first, or the film will not bond evenly.

Pros:
– Clear glossy finish gives concrete a fresh, wet look
– Waterproofs driveways, garage floors, and sidewalks
– Transparent coat keeps the concrete texture visible
– One-gallon size suits smaller jobs and test sections

Cons:
– Glossy film can feel slick when wet unless a grip additive is used
– Needs sound, clean concrete for even bonding
– One gallon covers a limited area on a full driveway

Specs

  • Type: Clear glossy concrete sealer
  • Volume: 1 gallon
  • Finish: Clear glossy
  • Application: Brush, roller, or sprayer
  • Surface: Concrete driveways, floors, sidewalks, cinderblock

How to Choose

Begin with the surface. Asphalt driveways need asphalt-compatible coatings and fillers: rubberized coatings like Liquid Rubber Driveway Restore and acrylic crack fillers like Red Devil 0637. Concrete driveways need concrete chemistry: deep-soak silane-siloxane sealers like the Armor SX5000 pair, or a clear film sealer like Americrete A-1300. Using an asphalt product on concrete, or a concrete sealer on asphalt, wastes material and delivers poor results.

Next, judge the condition. A sound driveway with faded color and hairline cracks is a coating job: clean it, fill the cracks, and apply two thin coats. A driveway with wide cracks, potholes, or settled sections needs repair first, because no sealer bridges a structural gap. For narrow cracks, a cartridge filler gives the cleanest result; for rough, worn asphalt, a filler-loaded coating or resurfacer rebuilds the surface.

Consider the finish you want. Deep-soak sealers keep the natural look and add no sheen, which suits pavers and brick. Film sealers add gloss and deepen color, which suits smooth concrete. Glossy films can feel slick in rain, so add a grip additive or choose a matte deep-soak sealer for steep or shaded driveways.

Check the weather window before you buy. Most sealers need a dry surface, temperatures above 50 degrees Fahrenheit, and at least 24 to 48 hours without rain. Water-based coatings dry slower in humidity, while solvent sealers need ventilation. Plan the job for a stretch of dry days, and keep vehicles off the driveway until the coating has fully cured.

Finally, measure before ordering. A five-gallon pail of asphalt coating covers roughly 250 square feet at the recommended thickness, while deep-soak concrete sealers stretch further because they soak in rather than build a film. Measure the driveway length and width, divide by the coverage figure on the listing, and round up to the next whole pail so you do not run short mid-coat.

FAQ

Can I apply driveway sealer over an old sealed driveway?

Yes, in most cases, as long as the old coating is sound and well bonded. Clean the surface thoroughly, remove loose or flaking material, and fill open cracks first. If the old sealer is peeling in large sheets, remove the loose sections before recoating so the new coat bonds to solid pavement.

How long should I wait before driving on a newly sealed driveway?

Allow at least 24 to 48 hours for foot traffic and 48 to 72 hours before parking a vehicle, and longer in cool or humid weather. Driving on a coating that has not fully cured can leave tire marks and pull up soft material. Check the drying guidance on the product listing for the exact cure time.

Do concrete driveways need sealer, or is it only for asphalt?

Concrete benefits from sealing too. A deep-soak sealer blocks water, de-icing salts, and oil from soaking into the pores, which helps prevent freeze-thaw spalling and staining. Asphalt sealers and concrete sealers use different chemistry, so choose a product made for your surface.

How often should a driveway be sealed?

Most asphalt driveways benefit from a fresh coat every two to three years, depending on traffic, sun exposure, and winter salt use. Concrete driveways sealed with a deep-soak product often hold up three to five years before reapplication. When water stops beading and the surface looks faded or dusty, it is time to seal again.

Conclusion

The best driveway sealer is the one matched to your surface and its condition. Liquid Rubber Driveway Restore leads for full asphalt renewal, the Armor SX5000 pair covers concrete in water-based and solvent-based forms, Red Devil 0637 handles narrow cracks with a caulking gun, and Americrete A-1300 adds a clear glossy finish to concrete. Clean the surface, repair the cracks, mind the weather window, and apply two thin coats for a finish that holds up through rain, salt, and daily traffic.

Explore Our Guides & Free Tools