- Top Pick: VNAF93 BPS1FA30 Aluminum Mesh Grease Filter, 2-Pack
- Runner-up: Air Filter Factory 41F Grease Mesh Carbon Combo Filter
- Also consider: Broan-NuTone 41F Replacement Charcoal Filter
The best range hood filters for most kitchens are the VNAF93 BPS1FA30 two-pack for Broan and NuTone Allure hoods, the Air Filter Factory 41F combo for ductless Broan and NuTone hoods, the genuine Broan-NuTone 41F charcoal filter for odor control, the HASMX aluminum grease filter for GE hoods, and the 99JGDAX cut-to-fit carbon sheet for hoods with unusual sizes. A good filter traps grease before it coats the blower and the ductwork, and a charcoal layer takes cooking odors out of the air that comes back into the room. The right choice starts with the size and shape of the old filter, because a filter that does not sit flat in the frame will let greasy air slip past it.
Range hood filters fall into three groups. Washable aluminum mesh filters catch grease and can be cleaned and used again for years. Disposable charcoal filters catch odors in ductless hoods and must be replaced on a schedule. Cut-to-fit carbon sheets cover hoods whose filters are no longer sold in a standard size. This guide covers all three groups, with five picks that fit common Broan, NuTone, Whirlpool, and GE hoods, and with the measurements and part numbers you need to match a filter to your hood.
As an Amazon Associate, we earn from qualifying purchases.
Table of Contents
- How to Choose a Range Hood Filter
- VNAF93 BPS1FA30 Aluminum Mesh Grease Filter, 2-Pack
- Air Filter Factory 41F Grease Mesh Carbon Combo Filter
- Broan-NuTone 41F Replacement Charcoal Filter
- HASMX Aluminum Replacement Grease Filter for GE WBX8406
- 99JGDAX Cut-to-Fit Activated Carbon Filter Sheet, 2-Pack
- Frequently Asked Questions
- Conclusion
- Product and ASIN Reference
How to Choose a Range Hood Filter
Start by pulling the old filter out of the hood and measuring it. Measure the length and width to the nearest eighth of an inch, and measure the thickness too, because a filter that is too thick will not seat in the frame and a filter that is too thin will rattle and leave gaps. Write down the part number printed on the old filter or in the hood manual, and match it against the replacement list on the listing.
Next, decide whether your hood vents outside or recirculates air back into the kitchen. Ducted hoods need a grease filter, and a washable aluminum mesh filter is the usual choice because it lasts for years with regular cleaning. Ductless hoods need a charcoal filter as well, because the air comes back into the room and only carbon takes odors out of it. Some filters combine both jobs in one frame, with a mesh layer for grease and a carbon layer for odors. Those combo filters are convenient, but the carbon layer still wears out, so the whole filter has to be replaced on a schedule even though the mesh part could be washed.
Check the cleaning and replacement schedule before you buy. Aluminum mesh filters should be washed every month or two in a sink with hot water and dish soap, or in a dishwasher if the maker says the filter is dishwasher safe. Charcoal filters cannot be washed at all, and washing one destroys its ability to trap odors, so plan on replacing a charcoal filter every three to six months in a kitchen that cooks often, and every six to twelve months in a kitchen that cooks less. Cut-to-fit sheets are the most flexible option for an old or unusual hood, but they need to be trimmed to size and held in place by the old frame or a retaining clip.
VNAF93 BPS1FA30 Aluminum Mesh Grease Filter, 2-Pack
The VNAF93 BPS1FA30 two-pack is the most practical pick for a Broan or NuTone Allure hood that vents outside. Each filter measures 11 and three-quarter inches by 14 and one-quarter inches, which matches the BPS1FA30 slot used across the Allure line and a long list of Whirlpool hoods. The frame is aluminum mesh, so grease collects on the layered metal instead of passing into the blower, and the filter can be washed and put back in service instead of being thrown away. Two filters in the box means one can be in the hood while the other is drying after a wash, so the hood is never left without a filter.
Fit is the main thing to check with this pick. The listing names a long run of compatible models, including Broan-NuTone QS130 hoods in several finishes, Whirlpool GXW6530 and GXW6536 hoods, Whirlpool UXT5530 and UXT5536 hoods, and Whirlpool WVW51 and WVW53 hoods. That breadth is helpful, but it also means the buyer has to confirm the model number on the hood label rather than guessing from the brand name alone. Measure the old filter first, because a filter that is a quarter inch too long will not slide into the track, and a filter that is a quarter inch too short will leave a gap at the edge.
The mesh construction is the standard multi-layer aluminum design used across the industry. Grease droplets hit the mesh, cool, and stick, while air keeps moving through the open layers. Over weeks of cooking the mesh loads up and airflow drops, which is why a monthly wash matters. The filter has no carbon layer, so it does nothing for odors on its own. That is the right trade for a ducted hood, where odors leave through the duct, but the wrong trade for a ductless hood. One quirk to note is the brand name in the product information, which reads VNAF93, while the listing title leads with the part number BPS1FA30. Match the part number and the size, not the brand name. The manufacturer part number is 99010299 S99010305, which replaces Broan part 99010299, so a buyer with an old filter marked 99010299 has a direct match.
Specs
| Spec | Detail |
|---|---|
| ASIN | B0C1ZF3CPM |
| Size | 11.75 x 14.25 inches |
| Material | Aluminum mesh |
| Filter shape | Rectangular panel |
| Pack | 2 filters |
| Manufacturer part number | 99010299 S99010305 |
| Replaces | Broan 99010299, S99010299, S99010305 |
| Washable | Yes |
| Charcoal layer | No |
Air Filter Factory 41F Grease Mesh Carbon Combo Filter
The Air Filter Factory 41F is the most convenient pick for a ductless Broan or NuTone hood, because it does two jobs in one frame. One side is aluminum mesh that catches grease, and the other side is a charcoal carbon layer that takes cooking odors out of the air before it returns to the kitchen. The filter measures 8.75 inches by 10.5 inches and is 0.44 inches thick, which matches the 41F slot used across the Broan-NuTone 41000 and 46000 series and many related hoods. The product information lists the material as aluminum and charcoal carbon, and the construction as aluminum mesh with charcoal carbon.
Compatibility is the strong point of this filter. The listing names a very long list of hoods, including Broan-NuTone 41000, 412401, 413001, 413601, 414201, 46000, 462404, 463002, and 464204 models, plus the ACS30 and BU230, BU324, and BUEZ1 lines. That breadth covers most of the small under-cabinet ductless hoods sold over the last two decades. The model number in the product information is 41F, and the part number is 41F-97007696-97005687, which ties it to Broan part numbers 97007696 and 97005687.
The combo design has one trade-off that the buyer should understand before ordering. The mesh layer can be washed, but the carbon layer cannot, and once the carbon is spent the whole filter has to go. That means the replacement schedule follows the carbon, not the mesh, and in a kitchen that cooks often the filter should be changed every three to six months. The product information states that the filter is not discontinued by the manufacturer, which is reassuring for a part that fits so many older hoods, but it does not change the replacement schedule.
Thickness is worth a careful check. At 0.44 inches this filter is a little thicker than the genuine Broan 41F charcoal filter, which measures 0.375 inches, so a hood with a tight frame may hold it snugly. Most 41F slots accept both thicknesses, but a buyer with a hood that already fits tightly should measure the slot depth before ordering.
Specs
| Spec | Detail |
|---|---|
| ASIN | B07DP4SRH6 |
| Size | 8.75 x 10.5 x 0.44 inches |
| Material | Aluminum, charcoal carbon |
| Construction | Aluminum mesh, charcoal carbon |
| Model | 41F |
| Part number | 41F-97007696-97005687 |
| GTIN | 00842477112332 |
| Replaces | Broan 41F, 97007696, 97005687 |
| Washable | Mesh layer only; carbon layer is disposable |
| Discontinued by manufacturer | No |
Broan-NuTone 41F Replacement Charcoal Filter
The genuine Broan-NuTone 41F is the pick for a buyer who wants the original equipment part rather than an aftermarket copy. It is a charcoal filter only, with no mesh layer, made for ductless Broan-NuTone hoods where a separate grease filter already sits in the hood. The model number in the product information is S97007696, and the filter measures 8.75 inches by 10.5 inches. The product information lists the material as charcoal, and the listing describes it as a genuine replacement part for the ductless range hood series.
Fitment covers the same family of hoods as the aftermarket 41F filters, including the 41000, 35000, 38000, 39000, 44000, 45000, and 46000 series, plus the RL6100, RL6200, RL6300, and SL6200 lines and the Microtek System I and II hoods. The listing also notes that the filter can be used on any BU2 and BU3 series hood. That range makes it the safe choice when the buyer is unsure which aftermarket copy matches, because the genuine part is the reference that the copies are measured against. The date first available in the product information is January 16, 2007, which shows how long this part has been in production.
The charcoal-only design is both the strength and the limit of this filter. It does one job, trapping odors in a ductless hood, and it does it without a mesh layer getting in the way. But it cannot be washed, and it cannot be cleaned in a dishwasher. Once the carbon is saturated, odors pass straight through, so the filter has to be replaced every six to twelve months depending on how often the kitchen cooks. The listing is clear that the hood itself is sold separately, which matters for a buyer replacing a whole hood rather than a filter. One point of care is the size. The United States listing gives the footprint as 8.75 by 10.5 inches, while a Canadian listing for the same part gives the full dimensions as 8.75 by 10.5 by 0.375 inches. That thickness is a little less than the 0.44-inch aftermarket combo filter, so the genuine filter slides into a tight slot more easily. A buyer replacing an aftermarket combo filter with this genuine charcoal filter should check whether the hood also needs a separate grease filter in the same slot, because the two products are not interchangeable in a hood that has only one filter position.
Specs
| Spec | Detail |
|---|---|
| ASIN | B00DM8KL0G |
| Size | 8.75 x 10.5 inches |
| Thickness | 0.375 inches |
| Material | Charcoal |
| Model | S97007696 |
| Brand | Broan-NuTone |
| Date first available | January 16, 2007 |
| Replaces | Broan 41F, S97007696 |
| Washable | No |
| Charcoal layer | Yes, charcoal only |
HASMX Aluminum Replacement Grease Filter for GE WBX8406
The HASMX aluminum grease filter is the pick for a GE hood that uses the WBX8406 filter. It measures 9 inches by 10.5 inches and is one-eighth of an inch thick, which is thinner than most range hood filters and matches the shallow slot in the GE hoods it fits. The material is aluminum, the construction is a mesh panel, and the listing states that it ships from Amazon and is sold by HASMX. The listing names the part numbers it replaces: GE WBX8406, American Metal Filter RHP0808 and RBF0901, and Homefilter HF120.
That cross-reference list is the most useful part of the listing, because the same filter shape is sold under several part numbers across GE and aftermarket brands. A buyer whose old filter is marked RHP0808 or HF120 has the same match as a buyer whose old filter is marked WBX8406, and the listing makes that clear. The thin profile is worth noting. At one-eighth of an inch thick, this filter slides into a slot that a standard quarter-inch filter would jam in, but it also means the mesh has fewer layers than a thicker filter, so it should be washed more often to keep airflow up. Cleaning follows the usual routine for aluminum mesh. Hot water and dish soap lift cooking grease, and a dishwasher cycle handles a filter that has been left for a while, as long as the buyer checks that the frame is not bent before putting it back. A bent frame leaves a gap at the edge, and greasy air will take the gap rather than the mesh. The filter has no charcoal layer, so it suits a ducted GE hood, and a buyer with a ductless GE hood will need a separate charcoal filter in addition to this grease filter.
Specs
| Spec | Detail |
|---|---|
| ASIN | |
| Size | 9 x 10.5 x 0.125 inches |
| Material | Aluminum |
| Construction | Mesh panel |
| Replaces | GE WBX8406, American Metal Filter RHP0808, RBF0901, Homefilter HF120 |
| Washable | Yes |
| Charcoal layer | No |
| Ships from | Amazon |
| Sold by | HASMX |
99JGDAX Cut-to-Fit Activated Carbon Filter Sheet, 2-Pack
The 99JGDAX cut-to-fit carbon sheet is the pick for a hood whose filter size is no longer sold as a standard part. Each sheet measures 16 inches by 48 inches and is 0.2 inches thick, and the pack holds two sheets, which is enough material to cut several replacement filters from one sheet. The model number in the product information is LM-CF-301, and the listing describes the sheet as an activated charcoal carbon vent filter for range hoods and air conditioning vents. The buyer trims the sheet to the size of the old filter with scissors and fits it into the old frame or behind a retaining clip.
The sheet is only a carbon layer, so it traps odors and smoke particles without catching grease the way a mesh filter does. In a ducted hood it works best as a second layer behind a washable mesh filter, and in a ductless hood it works as the odor layer that sits above the grease filter. A buyer who cuts the sheet to replace a mesh grease filter outright will find grease reaching the blower faster than before.
The replacement schedule is short. The listing says to change the filter every one to three months, which is faster than the three-to-six-month schedule for a framed charcoal filter, because the sheet is thin and the carbon load is spread across a large area once it is cut down. The product information gives the product dimensions as 15.75 by 47.24 by 0.2 inches, which is the sheet as packed rather than as cut, so the buyer should measure the old filter and allow a small margin for trimming rather than trusting the packed size. The listing also mentions a thinner 0.125-inch packing, so the buyer should confirm that the order is for the 0.2-inch sheet picked here and not the thinner variant.
Specs
| Spec | Detail |
|---|---|
| ASIN | B0BVQRJRNB |
| Sheet size | 16 x 48 x 0.2 inches |
| Packed dimensions | 15.75 x 47.24 x 0.2 inches |
| Material | Activated charcoal carbon |
| Model | LM-CF-301 |
| Pack | 2 sheets |
| Replacement schedule | Every 1 to 3 months |
| Washable | No |
Frequently Asked Questions
How do I know which size range hood filter I need?
Measure the old filter with a tape measure, length and width to the nearest eighth of an inch, and measure the thickness as well. Then match those numbers and the part number on the old filter against the listing. A filter that is close in size is not good enough, because a gap at the edge lets greasy air bypass the filter entirely.
Can I wash a charcoal range hood filter?
No. Charcoal filters cannot be washed, and putting one in water or a dishwasher destroys the carbon layer that traps odors. Washable filters are aluminum mesh grease filters, which can be cleaned in a sink with hot water and dish soap or in a dishwasher if the maker says so. A combo filter has a washable mesh layer and a disposable carbon layer, so the whole filter still has to be replaced on the carbon schedule.
How often should I replace a range hood filter?
A washable aluminum mesh filter lasts for years as long as it is washed every month or two and the frame stays straight. A charcoal filter should be replaced every three to six months in a kitchen that cooks often, and every six to twelve months in a kitchen that cooks less. A cut-to-fit carbon sheet should be changed every one to three months, because the thin sheet loads up faster than a framed filter.
What is the difference between a mesh filter and a baffle filter?
A mesh filter uses layered aluminum screen to catch grease droplets as air passes through, and it is the common choice for under-cabinet hoods. A baffle filter uses angled stainless steel channels that force air to change direction, so grease drops out into a tray, and it is the common choice for professional and commercial hoods. Baffle filters are sold mostly as parts for a specific hood rather than as universal replacements, which is why this guide focuses on mesh and charcoal filters that fit common home hoods.
Conclusion
The right range hood filter is the one that matches your hood by size and part number, and that matches your venting by filter type. The VNAF93 BPS1FA30 two-pack covers Broan and NuTone Allure hoods that vent outside, with a spare filter ready while one is being washed. The Air Filter Factory 41F combo covers ductless Broan and NuTone hoods in one frame, with mesh for grease and carbon for odors. The genuine Broan-NuTone 41F charcoal filter is the original equipment choice for odor control in the same ductless hoods. The HASMX aluminum filter covers GE hoods that use the WBX8406 part, including its aftermarket cross-references. The 99JGDAX cut-to-fit carbon sheet covers any hood whose standard filter is no longer sold, as long as the buyer is willing to trim it to size.
Measure the old filter before ordering, confirm the part number, and check whether the hood vents outside or recirculates air. Wash mesh filters on a regular schedule, replace charcoal filters before odors return, and the hood will keep the kitchen air cleaner with less grease on the cabinets.



Write Your Review
No reviews yet. Be the first to share your experience!