⏱ 14 min read  ·  ✅ Updated Nov 2026
⭐ Key Takeaways
Quick answer: Our top pick is RadonAway RP145c, with RadonAway GP501c as a strong alternative.

A radon mitigation fan is the part of a sub-slab depressurization system that does the actual work. A pipe runs from beneath the slab or membrane up through the house and out the roof, and the fan pulls radon-laden soil gas out of that pipe and vents it above the roofline before it can enter the living space. Without a fan that is sized for the slab and the pipe run, even a well-sealed system can leave indoor radon levels higher than they should be.

The fans below cover the full range of home situations, from a tight, low-permeability slab that needs high suction to a large, porous slab that needs high airflow, plus a sidewall system for homes where a roof vent is not practical. Each one is a dedicated radon fan, built with sealed housings and continuous-duty motors, and each is available as a standalone fan rather than a kit that forces a full system purchase.

As an Amazon Associate, we earn from qualifying purchases.

Table of Contents

RadonAway RP145c

The RadonAway RP145c is the general-purpose workhorse of this roundup, and it is the fan to start with when a home has a standard four-inch sub-slab pipe and no unusual soil conditions. It moves 166 cubic feet per minute at zero static pressure and holds 110 cubic feet per minute at half an inch of water column, which is enough airflow for a typical slab while still delivering meaningful suction. Its maximum operating pressure of 1.7 inches of water column gives it enough pull for tighter soils, where a weaker fan would stall and lose flow. The fan is HVI certified for its published airflow, ETL listed, and built for indoor or outdoor mounting on the vent pipe.

One detail matters when ordering. RadonAway sells the same fan under two listings: the current RP145c, part number 23030-1, code B00FIV1SZM, and the older RP145, code B00294RBFM. Both codes describe the same fan with the same motor, specifications, and five-year warranty, so only one belongs in a system. Confirm part number 23030-1 before ordering, and do not buy both codes expecting two different fans.

The RP145c is a quiet fan for its class, and RadonAway publishes a sound level that keeps it unobtrusive when mounted on an exterior wall or in an attic. It draws between 46 and 72 watts depending on the load, which keeps running costs modest for a device that runs continuously, day and night, for years. The housing is sealed to inhibit radon leakage at the seams, and the fan is thermally protected with a continuous-duty motor rated at 3,000 revolutions per minute. It mounts directly on the duct pipe or with an optional mounting bracket, and it accepts three-inch or four-inch Schedule 20 or 40 PVC pipe.

For most homes, this is the right balance of airflow, suction, and efficiency. A very tight slab or a long pipe run may need the high-suction GP501c below, but the RP145c covers the broad middle of residential mitigation work. It is also the fan RadonAway recommends as the replacement for older HP190 and HP2190 installations, which makes it a sensible choice when an aging fan finally gives out.

Specs

Specification Detail
Brand RadonAway
Model RP145c
Part number 23030-1
ASIN B00FIV1SZM
Airflow 166 CFM at 0 in. WC; 110 CFM at 0.5 in. WC
Maximum operating pressure 1.7 in. WC
Power draw 46 to 72 watts
Duct size 3 in. or 4 in. Schedule 20/40 PVC
Dimensions 8.5 in. H x 9.7 in. dia.
Weight 5.5 lbs
Inlet/outlet 4.5 in. OD
Certifications HVI certified, ETL listed
Warranty 5 years
UPC 720825263793

RadonAway GP501c

The RadonAway GP501c is the high-suction specialist in this roundup, built for slabs where the soil beneath is dense or the gravel layer is thin and a general-purpose fan cannot pull enough vacuum. Its maximum operating pressure reaches 3.8 inches of water column, more than double the RP145c, which lets it maintain airflow through restrictive sub-slab material that would choke a lower-pressure fan. At half an inch of water column it moves 66 cubic feet per minute, a modest airflow figure that reflects its design priority: suction first, volume second. Homes with tight clay soils, shallow gravel beds, or long horizontal pipe runs are the ones that need this kind of fan.

The GP501c is a three-inch fan, and that matters for planning. It connects to three-inch Schedule 20 or 40 PVC pipe, so a system built around four-inch pipe needs a reducer or a different fan. Its body is larger than the RP145c, at 13 inches high and 12.5 inches in diameter, and it weighs 12 pounds, so it needs a solid mounting point and a little more clearance. It draws between 68 and 146 watts, noticeably more than the general-purpose models, which is the price of its higher suction. Like the rest of the RadonAway line it is HVI certified, ETL listed, factory sealed against leakage, and covered by a five-year warranty.

This fan is not the right pick for a porous slab with a deep gravel layer. There it would pull hard against a system that does not need it, wasting energy and potentially drawing conditioned air from the house through slab cracks. It earns its place when a diagnostic test shows poor sub-slab communication or when a previous fan failed to bring levels down. Mitigators often reach for the GP501c as the second fan in a difficult job, after a general-purpose fan has proven insufficient. The honest approach is to test first, then buy the suction the slab actually needs rather than guessing.

Specs

Specification Detail
Brand RadonAway
Model GP501c
Part number 23005-1
ASIN B0028PICB4
Airflow 66 CFM at 0.5 in. WC
Maximum operating pressure 3.8 in. WC
Power draw 68 to 146 watts
Duct size 3 in. Schedule 20/40 PVC
Dimensions 13 in. H x 12.5 in. dia.
Weight 12 lbs
Inlet/outlet 3.5 in. OD
Certifications HVI certified, ETL listed
Warranty 5 years
Airflow at 0 in. WC not stated

Fantech Rn3

Check price on Amazon

The Fantech Rn3 is the largest fan in this roundup, and it is the pick for big slabs, commercial spaces, and homes where a single penetration has to serve a wide area. It moves 285 cubic feet per minute through a six-inch duct, which is far more airflow than any of the four-inch fans here can deliver. That volume matters when the slab is large or the sub-slab material is highly porous, because a high-flow fan can pull from a wider radius and keep the whole slab under negative pressure. The Rn3 is part of Fantech’s Rn series of radon fans, which are built specifically for radon mitigation rather than adapted from general ventilation duty.

The six-inch duct size is both the Rn3’s strength and its constraint. A system designed around four-inch pipe cannot use this fan without a transition, and the larger duct needs more space in the wall or chase. The Rn3 sits above the Rn2, which moves less air through a four-inch duct, and it is the largest model in the current Rn series. Confirm the six-inch duct size and the available mounting space before ordering, because a fan this size does not fit everywhere a four-inch fan does.

Because the Rn3 is a high-volume fan, it pairs best with a well-sealed slab and a properly sized pipe run. A leaky slab with many unsealed cracks can waste the extra airflow by pulling house air through the floor rather than soil gas from beneath it. Sealing sump pits, slab cracks, and pipe penetrations before installing a high-flow fan is good practice, and it lets the fan spend its capacity on radon rather than on conditioned air. For a large home, or for a slab that a smaller fan could not cover, the Rn3 is the straightforward answer.

Specs

Specification Detail
Brand Fantech
Model Rn3
ASIN B07F7FHGKQ
Airflow 285 CFM
Duct size 6 in.
Manufacturer Fantech
UPC 650737022204
Power draw not stated
Maximum operating pressure not stated
Dimensions not stated
Weight not stated
Warranty not stated

Systemair HP 190

The Systemair HP 190 is the compact budget pick in this roundup, a five-inch fan that delivers strong suction in a small package. It moves 157 cubic feet per minute and reaches a maximum operating pressure of 2.0 inches of water column, which gives it more pull than the general-purpose RP145c while keeping a smaller footprint. That combination suits homes where the vent pipe runs through a tight space, or where an older HP-series fan needs a direct replacement and the existing pipework is already sized for it.

The HP 190 uses a five-inch duct, which is unusual enough to plan around. Most residential systems use three-inch or four-inch PVC, so a five-inch fan needs the right pipe size or a transition fitting. Its higher operating pressure makes it a good match for slabs that are somewhat tight but not so restrictive that they need the GP501c, and its compact size makes it easier to fit into an existing vent run than the larger GP501c. The fan is built for continuous duty and for indoor or outdoor mounting, and it is a straightforward inline unit without extra features to fail.

One caution is that RadonAway’s own replacement guidance supersedes the HP series with the RP145c, so the HP 190 is best understood as a replacement for an existing HP installation or a choice for a system already piped for five-inch duct. A brand-new system is usually better served by a current-generation four-inch fan with published wattage and warranty details. For the right existing system, though, the HP 190 is a proven fan that does its job without fuss.

Specs

Specification Detail
Brand Systemair
Model HP 190
ASIN B000WA5076
Airflow 157 CFM
Maximum operating pressure 2.0 in. WC
Duct size 5 in.
Power draw not stated
Dimensions not stated
Weight not stated
Warranty not stated

Tjernlund RMS160 Sidewall Radon Mitigation System

Tjernlund RMS160 Sidewall Radon Mitigation System

Tjernlund RMS160 Sidewall Radon Mitigation System

Check price on Amazon

The Tjernlund RMS160 is the odd one out in this roundup, and that is exactly why it belongs here. Instead of mounting inline on a vertical vent pipe that runs to the roof, the RMS160 is a sidewall system: it vents radon through an exterior wall, which makes it the practical choice for homes where a roof vent is difficult, where the slab penetration is near an outside wall, or where an attic route is blocked. The system is sold as a complete sidewall unit, so it suits retrofits in finished homes where running a new pipe to the roof would mean opening walls and ceilings.

The RMS160 is a compact unit designed to fit tight spaces, and Tjernlund describes it as a quiet, high-capacity sidewall solution. Its form factor is the point: a homeowner who cannot route a vertical stack can still get a working depressurization system by going sideways instead of up. The unit is sold by Amazon.com, and its product information lists the Tjernlund brand, the RMS160 model, and the UPC 080956957436. Because it is a system rather than a bare inline fan, buyers should confirm what is included in the box and what additional pipe, fittings, or exterior hood parts the installation needs.

A sidewall system is not the default choice, and it should not be the first option for a new installation where a roof vent is feasible. Roof terminations keep the exhaust high and away from windows and doors, while a sidewall termination needs careful placement so the vented gas does not re-enter the house through a nearby opening. But when the house layout rules out a roof run, the RMS160 turns an impossible job into a workable one. It is the pick for the home that needs mitigation but cannot take a standard vertical stack.

Specs

Specification Detail
Brand Tjernlund
Model RMS160
ASIN B006WZKZA2
Type Sidewall radon mitigation system
UPC 080956957436
Sold by Amazon.com
Airflow not stated
Power draw not stated
Maximum operating pressure not stated
Dimensions not stated
Weight not stated
Warranty not stated

How to Choose

Start with the slab, not the fan. A diagnostic test that measures sub-slab communication tells a mitigator how easily air moves beneath the floor, and that result decides whether the job needs high airflow or high suction. A porous slab with a deep gravel layer needs volume, so a high-flow fan like the Rn3 or the RP145c fits. A tight slab with dense soil needs pressure, so a high-suction fan like the GP501c fits. Buying the most powerful fan without a diagnostic reading is a common mistake, because the wrong kind of power can waste energy and pull conditioned air out of the house.

Match the fan to the pipe. Three-inch, four-inch, five-inch, and six-inch fans are not interchangeable without transitions, and each transition adds resistance that eats into performance. The RP145c takes three-inch or four-inch pipe, the GP501c takes three-inch pipe, the HP 190 takes five-inch pipe, and the Rn3 takes six-inch pipe. Decide the pipe size first, then choose a fan that fits it, rather than buying a fan and adapting the system around it.

Check the mounting location and the termination. An inline fan can mount indoors or outdoors on the vent pipe, but an outdoor mount needs a fan rated for weather exposure, and any mount needs clearance for the fan body and for service access. A roof termination keeps exhaust above the roofline and away from openings, while a sidewall termination like the RMS160 needs careful placement so vented gas does not drift back through a nearby window or door. Plan the termination before buying, because it can rule a fan in or out.

Look at running costs and noise together. A mitigation fan runs continuously for years, so wattage matters more than it does for a fan that runs occasionally. The RP145c draws 46 to 72 watts, while the GP501c draws 68 to 146 watts, and that difference adds up over a year of nonstop operation. Noise matters too when the fan sits on an exterior wall near a bedroom, so check the published sound level and favor a quieter fan when the mounting point is close to living space. A fan that is cheap to buy but loud and power-hungry is not a bargain.

Confirm the warranty and the certifications. A five-year warranty is standard for the RadonAway line, and HVI certification means the published airflow was measured under a recognized standard rather than estimated. ETL listing confirms the fan meets electrical safety requirements. When a listing does not publish wattage, pressure, or warranty details, treat those fields as unknown rather than assuming they match a similar model.

Frequently Asked Questions

What size radon mitigation fan does a typical home need?

A typical single-family home with a standard four-inch sub-slab pipe and a moderately porous slab is usually served by a general-purpose four-inch fan such as the RP145c, which moves 166 cubic feet per minute at zero static pressure. Homes with tight soils need a high-suction fan instead, while very large slabs may need a high-flow fan or more than one penetration. A diagnostic test is the reliable way to size a fan, because soil conditions vary too much for a one-size rule to hold.

Can a radon mitigation fan be installed outdoors?

Yes, the fans in this roundup are rated for indoor or outdoor mounting on the vent pipe, and outdoor mounting on an exterior wall is common. The fan housing must be weather resistant, the electrical connection must be protected from moisture, and the fan should sit above the roofline termination or at a point where the exhaust cannot re-enter the house. In cold climates, an outdoor fan can also face condensation in the pipe, so the vent run should be planned to drain or to keep the fan clear of standing water.

How long does a radon mitigation fan last?

A continuous-duty radon fan typically lasts many years, and the RadonAway models in this roundup carry a five-year warranty. Actual service life depends on the motor, the operating load, and the environment, with outdoor fans in harsh climates sometimes wearing sooner than indoor ones. A fan that grows louder, vibrates, or loses airflow is a sign that the motor or bearings are wearing, and it should be checked before it fails outright. Keeping the vent pipe clear and the slab sealed helps the fan run at its intended load rather than fighting avoidable resistance.

Does a radon mitigation fan need to run all the time?

Yes. A sub-slab depressurization system only works while the fan is running, because the negative pressure beneath the slab disappears as soon as the fan stops. Turning the fan off lets radon accumulate under the slab and enter the house through cracks and joints, which defeats the purpose of the system. That is why wattage matters: a fan that draws 46 watts costs far less to run around the clock than one that draws 146 watts, and a fan chosen for the slab rather than oversized will use less power over its life.

Conclusion

The right radon mitigation fan is the one that matches the slab, the pipe, and the house, not the one with the biggest numbers on the listing. For most homes, the RadonAway RP145c is the sensible default: a general-purpose four-inch fan with solid airflow, respectable suction, modest power draw, and a five-year warranty. Homes with tight soils should step up to the high-suction RadonAway GP501c, while large slabs call for the high-flow Fantech Rn3. The Systemair HP 190 fits existing five-inch systems and tight mounting spots, and the Tjernlund RMS160 solves the homes where a roof vent is not possible. Whichever fan fits the job, confirm the part number, the duct size, and the specifications in the product information before ordering, and have the system checked after installation.

Explore Our Guides & Free Tools